Hot!Config change causes silent reload (6.2.2 and 6.2.3)

Author
btp
Bronze Member
  • Total Posts : 48
  • Scores: 2
  • Reward points: 0
  • Joined: 2007/09/26 02:02:57
  • Status: offline
2020/09/08 23:27:45 (permalink) 6.2
0

Config change causes silent reload (6.2.2 and 6.2.3)

80 x FG80E running 6.2.2 and 6.2.3. A couple of them seem to have 'management issues'. When issuing a basic config change (after a fresh reboot), the unit becomes unresponsive for approx 3-4 minutes. Seems to be any kind of config change. The traffic through the unit also stops. When looking on it through console, it seems quite unhappy:
 
config system ntp
   set source-ip 10.10.10.10
 
2020-09-08 17:31:46 cmdbsvr recv req_type=0(CMDB_REQ_COMMIT) from pid=214(/bin/newcli)
2020-09-08 17:31:46 [_svr_d_commit:2989] pid=214, object='system.ntp'
2020-09-08 17:31:46 cmdbsvr recv AF_MSG_T_CMDB_SVR_CHECK_DAEMON
2020-09-08 17:31:46 cmdbsvr recv req_type=22(CMDB_REQ_SEND_CMDB_EVENT) from pid=214(/bin/newcli)
2020-09-08 17:31:47 [check_if_need_revert_cfg:986] 42949666,4294967289,10
2020-09-08 17:31:47 System will reload in the next 9 seconds...
2020-09-08 17:31:47 cmdbsvr signal_init
2020-09-08 17:31:47 cmdbsvr send_event
NP6LITE: session timeout message missed, in=wan1 sip=34619742, dip=0a302f80, sport=443, dport=49371, proto=6
in_vtag=1, in_pid=249, t=0, valid=00000001
2020-09-08 17:31:48 [check_if_need_revert_cfg:986] 42949667,4294967289,10
2020-09-08 17:31:48 System will reload in the next 8 seconds...
NP6LITE: session timeout message missed, in=wan1 sip=34619742, dip=0a302f80, sport=443, dport=49370, proto=6
in_vtag=1, in_pid=249, t=0, valid=00000001
2020-09-08 17:31:49 [check_if_need_revert_cfg:986] 42949668,4294967289,10
2020-09-08 17:31:49 System will reload in the next 8 seconds...
NP6LITE: session timeout message missed, in=wan1 sip=d9920d89, dip=0a302f74, sport=5938, dport=59385, proto=6
in_vtag=1, in_pid=249, t=0, valid=00000001
2020-09-08 17:31:50 NP6LITE: session timeout message missed, in=wan1 sip=2843fe24, dip=0a302f84, sport=443, dport=65068, proto=6
in_vtag=1, in_pid=249, t=0, valid=00000001
[check_if_need_revert_cfg:986] 42949669,4294967289,10
2020-09-0NP6LITE: session timeout message missed, in=wan1 sip=0a301673, dip=0a302f14, sport=5002, dport=4334, proto=6
in_vtag=1, in_pid=249, t=0, valid=00000001
8 17:31:50 System will reload in the next 7 seconds...
2020-09-08 17:31:51 [check_if_need_revert_cfg:986] 42949670,4294967289,10
2020-09-08 17:31:51 System will reload in the next 6 seconds...
2020-09-08 17:31:52 [check_if_need_revert_cfg:986] 42949671,4294967289,10
2020-09-08 17:31:52 System will reload in the next 5 seconds...
NP6LITE: session timeout message missed, in=wan1 sip=2843fb84, dip=0a302f65, sport=443, dport=57263, proto=6
in_vtag=1, in_pid=249, t=0, valid=00000001
2020-09-08 17:31:53 [check_if_need_revert_cfg:986] 42949672,4294967289,10
2020-09-08 17:31:53 System will reload in the next 4 seconds...
2020-09-08 17:31:54 [check_if_need_revert_cfg:986] 0,4294967289,10
2020-09-08 17:31NP6LITE: session timeout message missed, in=wan1 sip=34619742, dip=0a302f80, sport=443, dport=49374, proto=6
in_vtag=1, in_pid=249, t=0, valid=00000001
NP6LITE: session timeout message missed, in=wan1 sip=14be8117, dip=0a302f80, sport=443, dport=49363, proto=6
in_vtag=1, in_pid=249, t=0, valid=00000001
:54 System will reload in the next 3 seconds...
NP6LITE: session timeout message missed, in=wan1 sip=c3e111f0, dip=0a302f8b, sport=443, dport=63683, proto=6
in_vtag=1, in_pid=249, t=0, valid=00000001
NP6LITE: session timeout message missed, in=wan1 sip=34619742, dip=0a302f80, sport=443, dport=49375, proto=6
in_vtag=1, in_pid=249, t=0, valid=00000001
NP6LITE: session timeout message missed, in=wan1 sip=0a30140e, dip=0a302f66, sport=5246, dport=37574, proto=17
in_vtag=1, in_pid=249, t=0, valid=00000001
2020-09-08 17:31:55 [check_if_need_revert_cfg:986] 0,4294967289,10
2020-09-08 17:31:55 System will reload in the next 2 seconds...
NP6LITE: session timeout message missed, in=wan1 sip=2843fb84, dip=0a302f6f, sport=443, dport=49908, proto=6
in_vtag=1, in_pid=249, t=0, valid=00000001
NP6LITE: session timeout message missed, in=wan1 sip=2843fe24, dip=0a302f85, sport=443, dport=65206, proto=6
in_vtag=1, in_pid=249, t=0, valid=00000001
NP6LITE: session timeout message missed, in=wan1 sip=0a30140e, dip=0a302f6e, sport=5247, dport=37579, proto=17
in_vtag=1, in_pid=249, t=0, valid=00000001
2020-09-08 17:31:57 [check_if_need_revert_cfg:986] 1,4294967289,10
2020-09-08 17:31:57 System will reload in the next 1 seconds...
2020-09-08 17:31:58 [check_if_need_revert_cfg:986] 2,4294967289,10
2020-09-08 17:31:58 0: config vdom
2020-09-08 17:31:58 0: edit VPN
2020-09-08 17:31:58 0: config vpn ipsec phase1-interface
2020-09-08 17:31:58 [_svr_d_clear:3071] pid=220, object='vpn.ipsec.phase1-interface.certificate'
2020-09-08 17:31:58 [_svr_d_clear:3071] pid=220, object='vpn.ipsec.phase1-interface.ipv4-exclude-range'
2020-09-08 17:31:58 [_svr_d_clear:3071] pid=220, object='vpn.ipsec.phase1-interface.ipv6-exclude-range'
2020-09-08 17:31:58 [_svr_d_clear:3071] pid=220, object='vpn.ipsec.phase1-interface.backup-gateway'
2020-09-08 17:31:58 [_svr_d_delete:3032] pid=220, object='vpn.ipsec.phase1-interface'
2020-09-08 17:31:59 [_svr_d_delete:3032] pid=98, object='system.interface'
2020-09-08 17:31:59 0: delete "4G-2"
2020-09-08 17:31:59 0: end
2020-09-08 17:31:59 0: end
2020-09-08 17:31:59 0: config vdom
2020-09-08 17:31:59 0: edit VPN
2020-09-08 17:31:59 0: config vpn ipsec phase1-interface
2020-09-08 17:31:59 [_svr_d_clear:3071] pid=220, object='vpn.ipsec.phase1-interface.certificate'
2020-09-08 17:31:59 [_svr_d_clear:3071] pid=220, object='vpn.ipsec.phase1-interface.ipv4-exclude-range'
2020-09-08 17:31:59 [_svr_d_clear:3071] pid=220, object='vpn.ipsec.phase1-interface.ipv6-exclude-range'
2020-09-08 17:31:59 [_svr_d_clear:3071] pid=220, object='vpn.ipsec.phase1-interface.backup-gateway'
2020-09-08 17:31:59 [_svr_d_delete:3032] pid=220, object='vpn.ipsec.phase1-interface'
2020-09-08 17:32:00 [_svr_d_delete:3032] pid=98, object='system.interface'
2020-09-08 17:32:00 0: delete "4G-1"
2020-09-08 17:32:00 0: end
2020-09-08 17:32:00 0: end
2020-09-08 17:32:00 0: config vdom
2020-09-08 17:32:00 0: edit VPN
2020-09-08 17:32:00 0: config vpn ipsec phase1-interface
2020-09-08 17:32:00 [_svr_d_clear:3071] pid=220, object='vpn.ipsec.phase1-interface.certificate'
2020-09-08 17:32:00 [_svr_d_clear:3071] pid=220, object='vpn.ipsec.phase1-interface.ipv4-exclude-range'
2020-09-08 17:32:00 [_svr_d_clear:3071] pid=220, object='vpn.ipsec.phase1-interface.ipv6-exclude-range'
2020-09-08 17:32:00 [_svr_d_clear:3071] pid=220, object='vpn.ipsec.phase1-interface.backup-gateway'
2020-09-08 17:32:00 [_svr_d_delete:3032] pid=220, object='vpn.ipsec.phase1-interface'
2020-09-08 17:32:00 [_svr_d_delete:3032] pid=98, object='system.interface'
2020-09-08 17:32:00 0: delete "IPSEC-1"
2020-09-08 17:32:00 0: end
2020-09-08 17:32:00 0: end
2020-09-08 17:32:07 0: config vdom
2020-09-08 17:32:07 0: edit root
2020-09-08 17:32:07 0: config vpn ipsec phase1-interface
2020-09-08 17:32:07 [_svr_d_clear:3071] pid=220, object='vpn.ipsec.phase1-interface.certificate'
2020-09-08 17:32:07 [_svr_d_clear:3071] pid=220, object='vpn.ipsec.phase1-interface.ipv4-exclude-range'
2020-09-08 17:32:07 [_svr_d_clear:3071] pid=220, object='vpn.ipsec.phase1-interface.ipv6-exclude-range'
2020-09-08 17:32:07 [_svr_d_clear:3071] pid=220, object='vpn.ipsec.phase1-interface.backup-gateway'
2020-09-08 17:32:07 [_svr_d_delete:3032] pid=220, object='vpn.ipsec.phase1-interface'
2020-09-08 17:32:07 [_svr_d_delete:3032] pid=98, object='system.interface'
2020-09-08 17:32:08 0: delete "MGMT_IPSEC"
2020-09-08 17:32:08 0: end
2020-09-08 17:32:08 0: end
2020-09-08 17:32:09 cmdbsvr recv AF_MSG_T_CMDB_SVR_CHECK_DAEMON
2020-09-08 17:32:09 cmdbsvr signal_init
2020-09-08 17:32:09 cmdbsvr recv AF_MSG_T_CMDB_SVR_CHECK_DAEMON
2020-09-08 17:32:09 cmdbsvr recv AF_MSG_T_CMDB_SVR_CHECK_DAEMON
2020-09-08 17:32:09 cmdbsvr recv AF_MSG_T_CMDB_SVR_CHECK_DAEMON
2020-09-08 17:32:09 cmdbsvr signal_init
unregister_vf: waiting for root to become free. rt_num = 2 vf_count=39
2020-09-08 17:32:20 cmdbsvr recv req_type=0(CMDB_REQ_COMMIT) from pid=151(/bin/dhcpcd)
2020-09-08 17:32:20 [_svr_d_commit:2989] pid=151, object='system.interface'
2020-09-08 17:32:20 cmdbsvr recv req_type=0(CMDB_REQ_COMMIT) from pid=151(/bin/dhcpcd)
2020-09-08 17:32:20 [_svr_d_commit:2989] pid=151, object='router.static'
2020-09-08 17:32:20 cmdbsvr recv req_type=0(CMDB_REQ_COMMIT) from pid=151(/bin/dhcpcd)
2020-09-08 17:32:20 [_svr_d_commit:2989] pid=151, object='router.static'
2020-09-08 17:32:20 cmdbsvr recv req_type=0(CMDB_REQ_COMMIT) from pid=151(/bin/dhcpcd)
2020-09-08 17:32:20 [_svr_d_commit:2989] pid=151, object='router.static'
2020-09-08 17:32:20 cmdbsvr recv req_type=0(CMDB_REQ_COMMIT) from pid=151(/bin/dhcpcd)
2020-09-08 17:32:20 [_svr_d_commit:2989] pid=151, object='router.static'
2020-09-08 17:32:20 cmdbsvr recv req_type=31(CMDB_REQ_BI_VD_SET_IPROPE) from pid=151(/bin/dhcpcd)
2020-09-08 17:32:20 cmdbsvr recv req_type=32(CMDB_REQ_BI_VD_SET_IPROPE6) from pid=151(/bin/dhcpcd)
2020-09-08 17:32:20 cmdbsvr recv AF_MSG_T_CMDB_SVR_CHECK_DAEMON
2020-09-08 17:32:20 cmdbsvr recv req_type=0(CMDB_REQ_COMMIT) from pid=151(/bin/dhcpcd)
2020-09-08 17:32:20 [_svr_d_commit:2989] pid=151, object='system.interface'
2020-09-08 17:32:20 cmdbsvr recv req_type=0(CMDB_REQ_COMMIT) from pid=151(/bin/dhcpcd)
2020-09-08 17:32:20 [_svr_d_commit:2989] pid=151, object='router.static'
2020-09-08 17:32:20 cmdbsvr recv req_type=0(CMDB_REQ_COMMIT) from pid=151(/bin/dhcpcd)
2020-09-08 17:32:20 [_svr_d_commit:2989] pid=151, object='router.static'
2020-09-08 17:32:20 cmdbsvr recv req_type=0(CMDB_REQ_COMMIT) from pid=151(/bin/dhcpcd)
2020-09-08 17:32:20 [_svr_d_commit:2989] pid=151, object='router.static'
2020-09-08 17:32:20 cmdbsvr recv req_type=31(CMDB_REQ_BI_VD_SET_IPROPE) from pid=151(/bin/dhcpcd)
2020-09-08 17:32:20 cmdbsvr recv req_type=32(CMDB_REQ_BI_VD_SET_IPROPE6) from pid=151(/bin/dhcpcd)
2020-09-08 17:32:20 cmdbsvr recv AF_MSG_T_CMDB_SVR_CHECK_DAEMON
2020-09-08 17:32:21 cmdbsvr set_iprope
__ha_ioctl()-210 t=12280: FW_CMD_CLEAR_BRIDGE_TIMER
__ha_ioctl()-65 t=12285: FW_CMD_CLEAR_HA_MODE
ip_session_change_id()-1529 t=12290: calls __ip_session_change_id()

__ha_ioctl()-210 t=16896: FW_CMD_CLEAR_BRIDGE_TIMER
__ha_ioctl()-210 t=16901: FW_CMD_CLEAR_BRIDGE_TIMER
NP6LITE: add vlif oid=68, vid=700
NP6LITE: insert iswa_spvact pht_idx = 220, 000af044 00000000 00000000 00000000
NP6LITE: insert tce_map pht_idx = 220, 408af044 00000010 00000000 00000000
NP6LITE: add vlif oid=68, vid=701
NP6LITE: insert iswa_spvact pht_idx = 24, 000af444 00000000 00000000 00000000
NP6LITE: insert tce_map pht_idx = 24, 40caf444 00000010 00000000 00000000
NP6LITE: lif dmz closed
NP6LITE: np6lite_hw_tbl_lif_update_mac: update mac
NP6LITE: Change LIF 2 MTU from 1500 to 1500
NP6LITE: HIF update rx buf len to 16384
NP6LITE: lif dmz opened
ADDRCONF(NETDEV_UP): dmz: link is not ready
NP6LITE: lif ha closed
NP6LITE: np6lite_hw_tbl_lif_update_mac: update mac
NP6LITE: Change LIF 3 MTU from 1500 to 1500
NP6LITE: HIF update rx buf len to 16384
NP6LITE: lif ha opened
ADDRCONF(NETDEV_UP): ha: link is not ready
NP6LITE: lif npu0_vlink0 closed
NP6LITE: Change LIF 16 MTU from 15324 to 15324
NP6LITE: HIF update rx buf len to 16384
NP6LITE: lif npu0_vlink0 opened
ADDRCONF(NETDEV_UP): npu0_vlink0: link is not ready
NP6LITE: lif npu0_vlink1 closed
NP6LITE: npu0_vlink0 link up, 1000Mbps
NP6LITE: Change LIF 17 MTU from 15324 to 15324
NP6LITE: HIF update rx buf len to 16384
NP6LITE: lif npu0_vlink1 opened
ADDRCONF(NETDEV_UP): npu0_vlink1: link is not ready
NP6LITE: lif port1 closed
NP6LITE: np6lite_lif_ethtool_sset: autoneg=1, duplex=0, speed=10
NP6LITE: Change LIF 4 MTU from 1500 to 1500
NP6LITE: HIF update rx buf len to 16384
NP6LITE: lif port1 opened
ADDRCONF(NETDEV_UP): port1: link is not ready
NP6LITE: npu0_vlink1 link up, 1000Mbps
NP6LITE: lif port1 closed
NP6LITE: np6lite_hw_tbl_lif_update_mac: update mac
NP6LITE: Change LIF 4 MTU from 1500 to 1500
NP6LITE: HIF update rx buf len to 16384
NP6LITE: lif port1 opened
ADDRCONF(NETDEV_UP): port1: link is not ready
NP6LITE: lif port2 closed
NP6LITE: np6lite_hw_tbl_lif_update_mac: update mac
NP6LITE: Change LIF 5 MTU from 1500 to 1500
NP6LITE: HIF update rx buf len to 16384
NP6LITE: lif port2 opened
ADDRCONF(NETDEV_UP): port2: link is not ready
NP6LITE: lif port3 closed
NP6LITE: np6lite_hw_tbl_lif_update_mac: update mac
NP6LITE: Change LIF 6 MTU from 1500 to 1500
NP6LITE: HIF update rx buf len to 16384
NP6LITE: lif port3 opened
ADDRCONF(NETDEV_UP): port3: link is not ready
NP6LITE: lif port4 closed
NP6LITE: np6lite_hw_tbl_lif_update_mac: update mac
NP6LITE: Change LIF 7 MTU from 1500 to 1500
NP6LITE: HIF update rx buf len to 16384
NP6LITE: lif port4 opened
ADDRCONF(NETDEV_UP): port4: link is not ready
NP6LITE: lif port5 closed
NP6LITE: np6lite_hw_tbl_lif_update_mac: update mac
NP6LITE: Change LIF 8 MTU from 1500 to 1500
NP6LITE: HIF update rx buf len to 16384
NP6LITE: lif port5 opened
ADDRCONF(NETDEV_UP): port5: link is not ready
NP6LITE: lif port6 closed
NP6LITE: port1 link up, 1000Mbps
NP6LITE: np6lite_hw_tbl_lif_update_mac: update mac
NP6LITE: Change LIF 9 MTU from 1500 to 1500
NP6LITE: HIF update rx buf len to 16384
NP6LITE: lif port6 opened
ADDRCONF(NETDEV_UP): port6: link is not ready
NP6LITE: lif port7 closed
NP6LITE: np6lite_hw_tbl_lif_update_mac: update mac
NP6LITE: Change LIF 10 MTU from 1500 to 1500
NP6LITE: HIF update rx buf len to 16384
NP6LITE: lif port7 opened
ADDRCONF(NETDEV_UP): port7: link is not ready
NP6LITE: lif port8 closed
NP6LITE: np6lite_hw_tbl_lif_update_mac: update mac
NP6LITE: Change LIF 11 MTU from 1500 to 1500
NP6LITE: HIF update rx buf len to 16384
NP6LITE: lif port8 opened
ADDRCONF(NETDEV_UP): port8: link is not ready
NP6LITE: lif port9 closed
NP6LITE: np6lite_hw_tbl_lif_update_mac: update mac
NP6LITE: Change LIF 12 MTU from 1500 to 1500
NP6LITE: HIF update rx buf len to 16384
NP6LITE: lif port9 opened
ADDRCONF(NETDEV_UP): port9: link is not ready
NP6LITE: lif port10 closed
NP6LITE: np6lite_hw_tbl_lif_update_mac: update mac
NP6LITE: Change LIF 13 MTU from 1500 to 1500
NP6LITE: HIF update rx buf len to 16384
NP6LITE: lif port10 opened
ADDRCONF(NETDEV_UP): port10: link is not ready
NP6LITE: lif port11 closed
NP6LITE: np6lite_hw_tbl_lif_update_mac: update mac
NP6LITE: Change LIF 14 MTU from 1500 to 1500
NP6LITE: HIF update rx buf len to 16384
NP6LITE: lif port11 opened
ADDRCONF(NETDEV_UP): port11: link is not ready
NP6LITE: lif port12 closed
NP6LITE: np6lite_hw_tbl_lif_update_mac: update mac
NP6LITE: Change LIF 15 MTU from 1500 to 1500
NP6LITE: HIF update rx buf len to 16384
NP6LITE: lif port12 opened
ADDRCONF(NETDEV_UP): port12: link is not ready
NP6LITE: lif wan1 closed
NP6LITE: np6lite_lif_ethtool_sset: autoneg=1, duplex=0, speed=10
NP6LITE: wan1 link up, 1000Mbps
NP6LITE: Change LIF 0 MTU from 1500 to 1500
NP6LITE: HIF update rx buf len to 16384
NP6LITE: lif wan1 opened
NP6LITE: lif wan1 closed
NP6LITE: np6lite_hw_tbl_lif_update_mac: update mac
NP6LITE: Change LIF 0 MTU from 1500 to 1500
NP6LITE: HIF update rx buf len to 16384
NP6LITE: lif wan1 opened
ADDRCONF(NETDEV_UP): wan1: link is not ready
NP6LITE: lif wan2 closed
NP6LITE: wan2 link up, 1000Mbps
NP6LITE: np6lite_lif_ethtool_sset: autoneg=1, duplex=0, speed=10
NP6LITE: Change LIF 1 MTU from 1500 to 1500
NP6LITE: HIF update rx buf len to 16384
NP6LITE: lif wan2 opened
NP6LITE: lif wan2 closed
NP6LITE: np6lite_hw_tbl_lif_update_mac: update mac
NP6LITE: Change LIF 1 MTU from 1500 to 1500
NP6LITE: HIF update rx buf len to 16384
NP6LITE: lif wan2 opened
ADDRCONF(NETDEV_UP): wan2: link is not ready
EXT3-fs: barriers not enabled
kjournald starting. Commit interval 5 seconds
EXT3-fs (mmcblk0p1): using internal journal
EXT3-fs (mmcblk0p1): mounted filesystem with writeback data mode
NP6LITE: wan1 link up, 1000Mbps
NP6LITE: wan2 link up, 1000Mbps
A9mp-i2c fb005000.i2c: i2c_xfer status9260
 

post edited by btp - 2020/09/08 23:29:47
#1

7 Replies Related Threads

    localhost
    Gold Member
    • Total Posts : 135
    • Scores: 25
    • Reward points: 0
    • Joined: 2015/05/21 02:47:51
    • Location: Zug, Switzerland
    • Status: offline
    Re: Config change causes silent reload (6.2.2 and 6.2.3) 2020/09/09 02:50:19 (permalink)
    0
    Does '#diagnose debug config-error-log read' show some information?
     
    If cmdb crashes it will initiate a reboot afair.
     
    #2
    btp
    Bronze Member
    • Total Posts : 48
    • Scores: 2
    • Reward points: 0
    • Joined: 2007/09/26 02:02:57
    • Status: offline
    Re: Config change causes silent reload (6.2.2 and 6.2.3) 2020/09/09 02:59:12 (permalink)
    0
    Nothing there..
    #3
    bommi
    Gold Member
    • Total Posts : 155
    • Scores: 14
    • Reward points: 0
    • Joined: 2016/08/03 03:42:49
    • Location: Germany
    • Status: offline
    Re: Config change causes silent reload (6.2.2 and 6.2.3) 2020/09/09 03:24:42 (permalink)
    0
    Go to "config sys global" and check the values for "cfg-save" and "cfg-revert-timeout".
    #4
    localhost
    Gold Member
    • Total Posts : 135
    • Scores: 25
    • Reward points: 0
    • Joined: 2015/05/21 02:47:51
    • Location: Zug, Switzerland
    • Status: offline
    Re: Config change causes silent reload (6.2.2 and 6.2.3) 2020/09/09 04:19:30 (permalink)
    0
    bommi
    Go to "config sys global" and check the values for "cfg-save" and "cfg-revert-timeout".


    Ah.. this good very will be the problem :)


    https://kb.fortinet.com/k....do?externalID=FD30912
    #5
    btp
    Bronze Member
    • Total Posts : 48
    • Scores: 2
    • Reward points: 0
    • Joined: 2007/09/26 02:02:57
    • Status: offline
    Re: Config change causes silent reload (6.2.2 and 6.2.3) 2020/09/09 04:27:42 (permalink)
    0
    Never seen this .. However; that indeed was the problem. Thanks a bunch!
     
    However - I never got the prompt
            # System will reboot if no input is received in the next xx seconds...
     
    So something is fishy 
     
    (How come I can't set your post as 'helpful' or 'answer'?)
    post edited by btp - 2020/09/09 08:19:18
    #6
    bommi
    Gold Member
    • Total Posts : 155
    • Scores: 14
    • Reward points: 0
    • Joined: 2016/08/03 03:42:49
    • Location: Germany
    • Status: offline
    Re: Config change causes silent reload (6.2.2 and 6.2.3) 2020/09/09 11:23:31 (permalink)
    0
    btp
    However - I never got the prompt
            # System will reboot if no input is received in the next xx seconds...

    This only gets displayed if you are connected using an serial console.
    #7
    btp
    Bronze Member
    • Total Posts : 48
    • Scores: 2
    • Reward points: 0
    • Joined: 2007/09/26 02:02:57
    • Status: offline
    Re: Config change causes silent reload (6.2.2 and 6.2.3) 2020/09/09 11:47:28 (permalink)
    0
    bommi
    This only gets displayed if you are connected using an serial console.


    I was - but guess it drowned in the debug output..
    #8
    Jump to:
    © 2020 APG vNext Commercial Version 5.5