Additional 0.0.0.0/0 address on all interfaces?

Author
brekkjen
New Member
  • Total Posts : 2
  • Scores: 0
  • Reward points: 0
  • Joined: 2020/03/25 06:00:40
  • Status: offline
2020/03/25 06:16:36 (permalink)
0

Additional 0.0.0.0/0 address on all interfaces?

Hi, when I run show system interface ? I get the following
 
fg100d-01 # show system interface ? 
name Name.
IF-xxx static 0.0.0.0 0.0.0.0 192.168.xxx.1 255.255.255.0 up disable vlan enable
IF-xxx static 0.0.0.0 0.0.0.0 192.168.xxx.1 255.255.255.0 up disable vlan enable
IF-xxx static 0.0.0.0 0.0.0.0 192.168.xxx.1 255.255.255.0 up disable vlan enable
IF-xxx static 0.0.0.0 0.0.0.0 192.168.xxx.1 255.255.255.0 up disable vlan enable
VPN_xxx static 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 up disable tunnel enable
dmz static 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 up disable physical enable
dmz-xxx static 0.0.0.0 0.0.0.0 192.168.xxx.1 255.255.255.0 up disable vlan enable
fext-wan1 dhcp 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 255.255.255.255 up disable fext-wan enable
ha1 static 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 up disable physical enable
ha2 static 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 up disable physical enable
mgmt static 0.0.0.0 0.0.0.0 192.168.xxx.1 255.255.255.0 up disable physical enable
 
Notice that every interface has a 0.0.0.0/0 address in addition to their correct address.
When i show the config on one interface the 0.0.0.0/0 address does not show
 
fg100d-01 # show system interface FL-xxx
config system interface
edit "FL-xxx"
set vdom "root"
set dhcp-relay-service enable
set ip 192.168.xxx.1 255.255.255.0
set allowaccess fabric
set device-identification enable
set role lan
set snmp-index 33
set dhcp-relay-ip "192.168.xx.xx"
set interface "port4"
set vlanid xx
next
end
 
I also just started using NetXMS for monitoring and that is reporting an invalid netmask of /0 on each interface
Is this normal or not? If not how can I fix it?
 
Thanks
Leif
 
#1

3 Replies Related Threads

    Toshi Esumi
    Expert Member
    • Total Posts : 2031
    • Scores: 186
    • Reward points: 0
    • Joined: 2014/11/06 09:56:42
    • Status: offline
    Re: Additional 0.0.0.0/0 address on all interfaces? 2020/03/26 09:44:09 (permalink)
    0
    "0.0.0.0 0.0.0.0" just means either you didn't statically configured IP or it hasn't pulled an IP via DHCP/pppoe yet. That's normal. In other words, "show sys int ?" is the way to see those dynamically assigned IPs to interfaces.
     
    #2
    brekkjen
    New Member
    • Total Posts : 2
    • Scores: 0
    • Reward points: 0
    • Joined: 2020/03/25 06:00:40
    • Status: offline
    Re: Additional 0.0.0.0/0 address on all interfaces? 2020/03/26 12:35:05 (permalink)
    0
    That would be normal if I didnt configure a static address, but all these interfaces has static addresses assigned to them. 
    For example this: IF-xxx static 0.0.0.0 0.0.0.0 192.168.xxx.1 255.255.255.0 up disable vlan enable
    This has 192.168.xxx.1/24 statically assigned to it, but also show 0.0.0.0/0
    In the GUI its no sign of the 0.0.0.0/0 address
     
     
    #3
    Toshi Esumi
    Expert Member
    • Total Posts : 2031
    • Scores: 186
    • Reward points: 0
    • Joined: 2014/11/06 09:56:42
    • Status: offline
    Re: Additional 0.0.0.0/0 address on all interfaces? 2020/03/26 13:45:53 (permalink)
    0
    I see. Now I understand what you mean.
    To be honest, I don't know what the "first" 0.0.0.0 0.0.0.0 mean. Seems to be only the "second" 0.0.0.0 0.0.0.0 is meaningful. I never questioned about it. Might be a good question to TAC through a ticket.
    #4
    Jump to:
    © 2020 APG vNext Commercial Version 5.5